features conductive plastic linear tapers audio tapers available pc board and bushing mount plastic bushing and plastic shaft withstands typical industrial washing processes rohs compliant* version available 3360 - 6 mm square sealed panel control *rohs directive 2002/95/ec jan. 27, 2003 including annex and rohs recast 2011/65/eu june 8, 2011. speci cations are subject to change without notice. the device characteristics and parameters in this data sheet can and do vary in different applications and actual device perfor mance may vary over time. users should verify actual device performance in their speci c applications. electrical characteristics standard resistance range linear ..............1k ohms to 1 megohm total resistance tolerance linear tapers ............................?0 % independent linearity .....................? % absolute minimum resistance ............................2 % or 2 ohms max. ......................... (whichever is greater) effective electrical angle ..240 ?nominal contact resistance variation ............................1 % or 3 ohms max. (whichever is greater) dielectric withstanding voltage (mil-std-202 ?method 301) sea level .............. 900 vac minimum 70,000 feet ........... 350 vac minimum insulation resistance .................. 1,000 megohms minimum power rating @ 70 ? (derate to 0 at 125 ? voltage limited by power dissipation or 200 vac, whichever is less) ............................................. .25 watts audio tapers .................... 0.125 watts theoretical resolution ............................... essentially in nite environmental characteristics operating temperature range .................................+1 ? to +125 ? storage temperature range ................................-55 ? to +125 ? temperature coef cient over storage temperature range ................................... ?,000 ppm/? vibration ......................................... 30 g total resistance shift .... ? % maximum voltage ratio shift..... ? % maximum shock............................................ 100 g total resistance shift ... ? % maximum voltage ratio shift...... ? % maximum load life ............................. 1,000 hours total resistance shift ......................... ?0 % trs maximum rotational life (no load) .. 50,000 cycles total resistance shift ........................... ? % trs maximum contact resistance variation ....................................3 % or 3 ohms, whichever is greater moisture resistance ........ mil-std-202, method 103, condition b total resistance shift ......................... ?0 % trs maximum ip rating .........................................ip 67 *rohs compliant versions available how to order 3360 y - 1 - 103 lf model terminal style designator single cup: c = in-line straight terminals side exit p = 5.08 mm x 2.54 mm triangular pattern rear exit y = 5.08 mm x 5.08 mm triangular pattern rear exit bushing designator 1 = standard resistance code terminations lf = 100 % tin-plated (rohs compliant) blank = 90 % tin / 10 % lead-plated (standard) standard resistance table resistance resistance (ohms) code 1,000 102 2,000 202 5,000 502 10,000 103 20,000 203 50,000 503 100,000 104 200,000 204 500,000 504 1,000,000 105 physical characteristics stop strength......... 5.65 n-cm (8 oz.-in.) mechanical angle .............310 ?nominal torque starting ........3.53 n-cm (5.0 oz.-in.) maximum running ........3.53 n-cm (5.0 oz.-in.) maximum mounting (torque on bushing) ............17 n-cm (1.5 lb.-in.) maximum [plastic bushing] weight ................................... 4.5 grams terminals ....................... solderable pins soldering condition ..........5 seconds at 360 ? maximum. recommended hand soldering using sn95/ag5 no clean solder, 0.025 wire diameter. marking .........manufacturer s trademark, model number, product code, terminal style, resistance code and date code flammability ........ conforms to ul94v-0 epoxy................... conforms to ul94v-1 hardware (purchased separately) nut ............................................ h-38-1 washer ..................................... h-37-5 popular distribution resistance values listed in boldface. special resistances available. 3360 y 503 247c0
*rohs directive 2002/95/ec jan. 27, 2003 including annex and rohs recast 2011/65/eu june 8, 2011. speci cations are subject to change without notice. the device characteristics and parameters in this data sheet can and do vary in different applications and actual device perfor mance may vary over time. users should verify actual device performance in their speci c applications. 3360 - 6 mm square sealed panel control product dimensions dimensions: mm (inches) rev. 02/13 common dimensions 3360c 3360p 3360y 3.35 (.131) 5.59 ?.25 (.220 ?.010) across flats 3.20 ?.25 (.126 ?.010) .38 (.015) min. standoff 2.54 ?.25 (.100 ?.010) 2.54 ?.25 (.100 ?.010) 6.35 ?.025 (.250 ?.010) mounting dia. 2.36 ?.050 (.093 ?.002) dia. 6.35 (.250) 5.44 (.214) min. full thread 12.70 ?.64 (.500 ?.025) 1/4-32 unef-2a threaded plastic bushing .33 (.013) min. standoff 3.91 ?.38 (.154 ?.015) 4.70 ?.38 (.185 ?.015) .64 ?.10 (.025 ?.004) wide .76 ?.25 (.030 ?.010) deep x adjustment slot 6.71 ?.25 (.264 ?.010) 6.78 ?.25 (.266 ?.010) 5.97 ?.89 (.235 ?.035) .46 ?.05 (.018 ?.002) solder plated copper pins dia. 1 2 3 .33 (.013) min. standoff 5.97 ?.89 (.235 ?.035) 2.54 ?.38 (.100 ?.015) 3.58 ?.38 (.141 ?.015) typ. 2.54 ?.25 (.100 ?.010) 2.54 ?.25 (.100 ?.010) 1 2 3 1 2 3 3 2 1 ccw cw wiper clockwise 5.97 ?.89 (.235 ?.035) 5.08 ?.25 (.200 ?.010) .97 ?.38 (.038 ?.015) 2.54 ?.25 (.100 ?.010) 2.54 ?.25 (.100 ?.010)
|
